How to Set Time on Hayward Pool Pump
LeonPosted: 11/1/2021
How do you turn off a timer? Somehow have 2 timers running?
Reply
InyoPools Product Specialist Matt S. Posted: 11/2/2021
Set the timer to begin and end at the same time.
Reply
AnonymousPosted: 10/29/2021
My freeze protection didn't work last winter and it cost me a filter head. I don't close my pool in the winter. This year I was trying to run 24/7 on my pump during the winter to prevent freezing. I set it up to start at 4 p and end at 4 p. Pump stays on but stops pumping water sometime later. Viewing cap has water so it's not dry. If I hit quick clean it starts pumping. I'm running 2300 rpm 24 hrs. It stops pumping sometime during the day. I bought this pump to save money over my single speed that ran 24/7 365 but I'm finding myself lost with this situation. I'm scared the freeze protection won't work again and next time may be more damage. Any ideas to remedy either situation
Reply
InyoPools Product Specialist Matt S. Posted: 11/1/2021
Maybe the schedule is getting confused because it is beginning and ending at the same time. Try setting the stop time to 3:45 or 3:59 pm, so there is no overlap.
Reply
KenPosted: 10/27/2021
I have followed programming but can't seem to get pump to work in standalone mode. I noticed in your video the timer activate light is on. My light is not on and after programming the pump won't start up. Any suggestions?
Reply
InyoPools Product Specialist Matt S. Posted: 10/29/2021
When you press Quick Clean, does the pump startup? Do you have an automation system wired to the pump, even though you directly program the speeds? Lastly, are you sure the programs are being saved after you set them?
Reply
James FPosted: 10/15/2021
Great info, I have a second timer set so I could run my pump 24 hours for initial installation, how do I disable the second timer?
Reply
InyoPools Product Specialist Matt S. Posted: 10/18/2021
I'd try setting the start and end time to the same value. Doing that should zero out the run time.
Reply
Matt RoppeltPosted: 7/22/2021
Is there a way to turn the pump on to run for straight 24 hours for a chemical clean?
Reply
InyoPools Product Specialist Matt S. Posted: 7/23/2021
There isn't a 24-hour override on this pump model like there are on other models like the Century V-Green. Your best option is to alter one of your schedules to run the desired clean cycle speed.
Reply
Michael RacanelliPosted: 5/17/2021
Plz help... Very important question: How do I temporarily turn the pump on, outside of the programmed ON time? For example: Lets say I have the pump programmed to shut off at 6pm. But at 7pm, I spontaneously decide that I need to turn it on for a while, and then later shut it off again. How do I do this??? Thank you sooo much. I look forward to hearing from you.
Reply
InyoPools Product Specialist Matt S. Posted: 6/4/2021
Press the Override/Clean button on the motor control.
Reply
LoriPosted: 5/2/2021
Good video. How do I use the Quick Clean button on the bottom right of the display? Thank you!
Reply
InyoPools Product Specialist Matt S. Posted: 5/13/2021
You should be able to press it and it will run at the factory default speed, 3450. You also have the option to program the quick clean speed and duration
Reply
AnonymousPosted: 8/24/2021
How do I raise the speed on the quick clean option? Thanks!
Reply
InyoPools Product Specialist Matt S. Posted: 8/24/2021
The Quick Clean mode runs at the MAX allowed speed and expires after 60 min. So, you would adjust your maximum allowed speed to change your QC mode, the process of which is shown in step 9.
Reply
LoriPosted: 5/13/2021
Thank you! Wasn't sure if I could press the button without programming it.
Reply
InyoPools Product Specialist Matt S. Posted: 5/14/2021
No problem, glad to help.
Reply
How to Set Time on Hayward Pool Pump
Source: https://www.inyopools.com/HowToPage/how-to-program-a-variable-speed-hayward-super-pump.aspx
0 Response to "How to Set Time on Hayward Pool Pump"
Post a Comment